Matrix™ is a high porosity biomedia that provides efficient biofiltration for the removal of nitrogenous waste. Matrix™ is a porous inorganic solid about 10 mm in diameter. Each liter of Matrix™ provides as much surface (>~700 m2) as 170 liters of plastic balls! Plastic bio-materials provide only external surface area, whereas Matrix™ provides both external and internal macroporous surface area. These macropores are ideally sized for the support of nitrifying and denitrifying bacteria. This allows Matrix™, unlike other forms of biomedia, to remove nitrate along with ammonia and nitrite, simultaneously and in the same filter.
Matrix™ is completely inert and will not breakdown. It need not be replaced. Since the majority of the bacteria are internal, Matrix™ may be rinsed when needed without damaging the filter. Matrix™ is compatible with all types of wet or wet-dry filters.
Use 250 mL of Matrix™ for each 100 L (25 US gallons) of water. Matrix™ may be placed in any kind of filter, and is particularly effective in a canister filter. Matrix™ is sufficiently large that no filter bag should be required for most applications. Matrix™ works well in drip tray systems, but you may find that the larger Pond Matrix™ is better suited for such applications.Use with Stability® to more rapidly establish the bio-filter.
Surface Area of Matrix, Eheim Substrat Pro, and JBL MicroMec
Two competitors, Eheim (Substrat Pro) and JBL (MicroMec) have advertised their own biological filter media (in both cases, sintered glass) and are claiming larger specific surface areas than our claim for Matrix.
For biological filter media, specific surface area (measured as surface area per gram of material, or surface area per some specified volume of material) is very important. These products provide surface sites for bacteria to attach and do their work. The greater the surface area per gram of medium, the greater the number of bacteria that can attach. Thus a high specific surface area is desirable.
There is a second consideration, and that is the size of the pores in the medium. Generally, with very large pore diameters, we have smaller specific surface area, so that is not good. This generally rules out pores above 10 microns in diameter. But we can go too far in the other direction. If we have a very large number of very, very small pores, then our specific surface area number will be phenomenal, but the medium will not work very well as a biological medium. This is due to physical limitations, specifically too small a volume to support bacterial growth, and the decreasing efficiency of fluid transport (necessary to carry nutrients to the bacteria and waste away from the bacteria) with very small pore sizes. (Small pores still play important roles in physical and chemical processes, such as adsorption.)
BET surface area measurements indicate that Matrix™ contains nearly 10 times the specific surface area of Substrat Pro, and more than 20 times the specific surface area of MicroMec. Practically all the specific surface area of both Substrat Pro and MicroMec are in the range of pore diameters to be biologically useful, while some of the surface area of Matrix is in pores that are reserved for physical and chemical processes, not biological processes. Estimates from two different pore geometries indicate that Matrix contains between 4 to 4.5 times the biologically active surface area of Substrat Pro, and between 8 to 9 times the biologically active surface area of MicroMec.
For a more in depth report on this study, click here.
250 mL, 500 mL, 1 L, 2 L, 4 L
A: Nothing’s wrong. The product is working just as it should. The removal of nitrates essentially comes down to one parameter: rate. The rate at which your tank is producing nitrates and the rate at which it can remove them. If you fill a bathtub with the spigot wide open and try to keep it from overflowing by draining it out of a straw, it won’t be long until it overflows. However, if you drain it at the same rate it fills, the level will always stay the same. Or, if it nearly fills up and then you drain it at a rate faster than it is filling, the level will drop. The same applies to nitrate removal. To lower nitrates you must equip your tank with the capacity to remove them at a rate greater than or equal to the rate of formation. So, if your nitrates are holding steady and you want them to come down, increase the amount of Matrix you are using or use de*nitrate in addition to the Matrix (de*nitrate will more efficiently remove nitrates per volume of product assuming a flow rate of not more than ~50 gallons/hour). If you need to use a higher flow rate, than stick with Matrix or try Pond Matrix, both of which support anaerobic denitrification at higher flow rates.
A: That depends on a number of things. If Matrix is doing the job for you (i.e. keeping nitrite/nitrate under control) then, no. If you’re running a flow rate higher than 50 gallons/hour, then you won’t be able to use de*nitrate anyway since it requires a flow rate slower than that to support the denitrifying bacteria. If filter size and capacity are an issue, then de*nitrate will provide a more efficient removal of nitrate per volume of product (i.e. you can use less de*nitrate by volume than Matrix to get the same denitrifying capacity). Also, de*nitrate has the capacity to remove nitrates by chemical absorption on initial use of the product, although if nitrate levels are very high (above 20 mg/L) we recommend a water change as the most economical approach to getting your nitrate level down before putting these products into service.
A: This all depends on the stage of biological establishment of your tank, placement of Matrix and flow rate. Generally you will start to see improvement in a couple of weeks but every situation varies.
A: It will work but not nearly as well, a canister filter is recommended.
A: No, It is an inert media that will not directly impact your pH.
A: If you have a fish load it would be extremely difficult to bring down your nitrates to zero (fish foods, waste being introduced on a daily basis). However, it will help maintain your nitrates at lower levels.
A: Not to worry! Matrix has some natural variations in color and size of the pieces, ranging from very light to quite dark. It is normal to see some color differences from one piece of Matrix to the next.
A: We certainly understand why people look at Matrix and compare it to pumice; they are both porous stones. But remember, not every porous stone is the same. Matrix is a specific type chosen for its extremely high porosity, pore size, durability, and inert nature. When you buy Matrix, you know what you are getting. It has been tested in the lab and in thousand of hobbyist's aquariums for more than a decade with excellent results. You aren't just purchasing the physical material when you buy a container of Matrix; you are purchasing the research which has sourced and tested this specific type of stone, and the assurance that it is safe for use in your aquarium.
A: Matrix is a biomedia, meaning it does not exhaust over time, so you should never need to replace it. That said it is possible for Matrix media to become clogged up with detritus and slime, so we recommend regular filter maintenance to ensure it continues working as efficiently as possible. The frequency with which a canister filter needs to be opened and cleaned out varies from tank to tank, but a good starting point is once a month.
A: We recommend that water flow through filter media in this order:
1. Mechanical filtration (filter floss, sponges, etc.)
2. Chemical filtration (MatrixCarbon, PhosGuard, Purigen, etc)
3. Biological filtration (Matrix)
Every filter is different, so the exact placement of Matrix will vary from brand to brand. Consult your filter’s instruction manual to find the direction of flow for your filter.